Moving magnet vs moving coil: cartridge loading guide

16 November 2026

The key to getting the best sound from your turntable setup is pairing the right phono stage with your chosen moving magnet (MM) or moving coil (MC) cartridge. MM and MC cartridges have very different electrical characteristics, so the way you load them into the phono stage makes a big difference to how they perform.

The two key loading parameters are resistance (impedance) and capacitance. These are set at the phono stage input to match the cartridge. A standard MM stage presents a 47 kΩ resistance and a modest total capacitance (combining cable and stage capacitance). MC cartridges typically need much lower input resistances, from 50 Ω to 1 kΩ, and capacitance is less critical.

What's the difference between MM and MC?

MM cartridges are electrically simpler and easier to match. The vast majority of cartridges are MM designs. MC cartridges offer potentially better sound quality, but come with more complex loading requirements.

MM cartridges have a built-in magnet and coil. The magnet is connected to the moving stylus. As the stylus tracks the grooves, it moves the magnet through the magnetic field, inducing a voltage in the coil. This voltage is passed to the phono stage, which then feeds it to your amplifier and speakers.

MM cartridges typically output 3–6 mV. They see a standard load impedance of 47 kΩ. This matches the 47 kΩ input impedance of most phono stages, which is why most MM cartridges can be used straight out of the box with most setups.

In contrast, MC cartridges are electrically more complex. They have coils affixed to the stylus, and a set of magnets mounted in the body of the cartridge. As the coils move in the grooves, it induces a current in the coils. This current is passed to the phono stage, which then feeds it to your amp and speakers.

MC cartridges typically output 0.2–0.6 mV, so they need more gain from the phono stage. The low output means they can't use the 47 kΩ input of a standard MM stage. Instead, they need an input resistance in the 50 to 1,000 Ω range to match their low internal impedance. This matches the internal impedance, allowing the maximum signal to be transferred to the phono stage.

MM loading: capacitance is key

For MM cartridges, the key loading parameter is capacitance, not resistance. An MM cartridge sees a standard 47 kΩ resistance at the phono stage input, and this value is effectively universal. The key variable is the total capacitance - the sum of the tonearm wiring, interconnect, and phono stage input capacitance.

Most MM cartridges specify a recommended capacitance range in their specifications. For example, a cartridge might recommend a total capacitance of 100–200 pF. This range will include the capacitance of the tonearm cable and interconnect, and the input capacitance of the phono stage. It's likely to be a relatively modest value.

If the total capacitance is too high, an MM cartridge will produce a treble peak and a bright sound. But if the total capacitance is too low, it will roll off the high frequencies. So it's important to get the total capacitance in the right ballpark. That's why many dedicated phono stages have an adjustable capacitance control.

MC loading: resistance is key

MC cartridges are dominated by the resistive loading, and capacitance is far less critical. An MC cartridge typically needs a low input resistance, from 50–1,000 Ω, to match its low internal impedance. This matches the internal impedance, allowing the maximum signal to be transferred to the phono stage. The key is to match the phono stage input impedance to the MC cartridge's impedance.

The recommended load impedance range for an MC cartridge is often 100 Ω to 1 kΩ for a low-output design. A commonly used guideline is to load an MC cartridge at about 10 times its internal impedance. So, for example, a cartridge with 10 Ω internal impedance would start around 100 Ω. But the optimal load can vary by quite a bit, depending on the cartridge and your system, so it's important to have a phono stage that can dial in the right value.

Many MC cartridges specify a recommended load impedance in their specifications. If you don't have a loadable phono stage, you can approximate the effect by using a step-up transformer (SUT) to raise the cartridge's output to MM levels. But you won't be able to dial in a precise load, so you can't fine-tune the sound.

Common loading options

A commercial MC-capable phono stage will typically have a range of loading options, often via DIP switches, rotary controls, or plugs. Values like 50 Ω, 100 Ω, 200 Ω, 500 Ω, and 1 kΩ are common.

Here's the loading options available on a popular production phono stage:

Gain (dB)Load 1Load 2Load 3Load 4
3347 kΩ---
4247 kΩ200 Ω47 Ω38 Ω
4847 kΩ200 Ω47 Ω38 Ω
6047 kΩ200 Ω47 Ω38 Ω

This example shows the loading options available at each gain level. There are four possible loads: 47 kΩ (suitable for MM), 200 Ω, 47 Ω, and 38 Ω. The 33 dB gain is MM-only; the 42, 48, and 60 dB options include MC loading.

Loading MC cartridges: a practical guide

If you're using a loadable MC-capable phono stage, here's a practical workflow for setting the load:

1. Consult the MC cartridge's specifications for a recommended load, if available.

2. If no recommendation is given, start with a load about 10 times the cartridge's internal impedance.

3. Listen to your system with the cartridge loaded at this initial value. Make a note of the sound.

4. Increase or decrease the load by a factor of 2, and take notes on how the sound changes. For example, if you started at 200 Ω, try 100 Ω, and then 500 Ω.

5. Continue to adjust the load by factors of 2, and take notes, until you find the sound you like best.